TI18102 First Order Tie Pilot (WIP)

[rakso]

Buenos días tropa,

Como yo también estoy en proceso de conseguir el alta de un piloto de la Primera Orden, abrimos un nuevo hilo WIP

Os dejo el enlace al CRL: http://databank.501st.com/databank/Cost ... irst_Order

Os dejo además el enlace al Black Squadron FO TIE Build Book V4 del escuadrón de pilotos donde se puede descargar el manual en formato PDF de la guía de montaje. Aunque está orientado al montaje de un casco SGB y armadura de KB props, incluye mucha información útil como el manual para el ensamblado del cinturón.

https://www.jrs501st.com/forums/viewtopic.php?t=14557

Iré actualizando el hilo según vaya recibiendo los diferentes componentes del traje y detallando lo que comenta el CRL de cada componente.

LISTA DE VERIFICACION
-----------------------------------------

1. CASCO: Recibido de SGB. En proceso de construcción.
2. BALACLAVA: Comprada en el LIDL.
3. NECKSEAL: Recibido de Aaron Lander
4. HOSE: Recibido
5. FLEXIBLE VAC SUIT (Flight Suit): Recibido de CrowProps.
6. CHEST ARMOR: Encargada a Shawn (Thorsson & Associates Workhop) en formato RAW (fiberglass).
7. BACK ARMOR AND YOKE: Encargada a Shawn (Thorsson & Associates Workhop) en formato RAW (fiberglass).
8. SHOULDER BELLS: Encargada a Shawn (Thorsson & Associates Workhop) en formato RAW (fiberglass).
9. VAMBRACE ARMOR (FOREARMS): Encargada a Shawn (Thorsson & Associates Workhop) en formato RAW (resina).
10. FLIGHT GLOVES: Recibidos de un artesano nacional
11. LIFE SUPPORT GEAR (CHEST BOXES): Pendiente de encontrar un modelo 3D para su impresión.
12. BELTS, BELT BOXES AND EJECTION HARNESS: Pendiente de encontrar un modelo 3D de las cajas para su impresión.
13. POSITIVE GRAVITY BOOTS: Recibidas de un artesano nacional
14: ACCESIORIO OPCIONAL, SE-44c Blaster Pistol: Recibido un kit impreso en 3D de Imperial Props 3D

Un poco de historia.
---------------------------------

Como primera opción para el casco y la armadura, me puse en contacto con el compañero navalgijon quien se comprometió a realizar un juego completo pero perdimos el contacto por lo que nunca pude recibir la armadura.
Como esta opción no cuajó, me recomendaron Miguel Ruiz (facebook) y después de realizar el pago completo, nunca llegue a recibir el encargo. Menos mal que por lo menos pude recuperar las 3/4 partes gracias a la reclamación de Paypal. El deposito inicial no pude recuperarlo porque se había pasado el plazo para la correspondiente reclamación en PayPal. No recomiento para nada este PropMaker.

Actualmente tengo un casco de SGB (Sky Gun Bro) en resina pendiente del acabado.
La armadura, la tengo solicitada a Shawn (Thorsson & Associates Workhop) por recomendación del Grupo de Pilotos FO de Facebook.

[rakso]

1. CASCO: En proceso de construcción

Esto es lo que dice el CRL:

•El casco tiene lentes planos o de burbujas, teñidos de color marrón o gris para oscurecer lo suficiente los ojos del cliente.
•Hay dos greeblis en forma de "pastilla de refresco" que sobresalen de las mejillas en diagonal hacia atrás desde las esquinas de las lentes de los ojos e incluso con los extremos del borde de la ceja. Estas pestañas tienen una ligera curvatura de 45 grados.
•Hay un greeblie tipo "tornillo" que sobresale de la sien derecha paralelo al borde de la ceja.
•Hay dos óvalos delgados y alargados adornados en plata sobre cada lente del ojo a ambos lados del casco.
•Hay una tapa de sensor (HUD) fijada en la parte superior del casco.
•Hay un puerto de manguera conectado a cada colmillo. Los puertos son de color metálico o plateado.
•La franja frontal está pintada de negro mate.
•Hay múltiples ranuras en la cara y la parte posterior del casco como se ve en la foto de referencia.
•IDENTIFICACIÓN. Se pueden agregar números en Aurebesh centrados sobre el borde de la ceja.
•Es posible que haya dos franjas o "lágrimas" de color burdeos o rojo en el casco para representar el estado de las Fuerzas Especiales. Las rayas comienzan en el borde inferior del sensor de orientación en la frente y continúan por el frente de la cara hasta la ranura inferior justo encima de cada puerto de manguera y terminan en una punta. Las rayas terminan en secciones justo encima y debajo de cada línea de ranura en el casco.
OPCIONAL Certificación de nivel dos (si corresponde):
*El aparato de orientación (HUD) es estático y no se mueve

Recibido el casco de SGB (Sky Gun Bro)



13/11/2023: El GML da el OK al modelo.

¿Cual sería el proceso correcto para pintarlo?

[rakso]

2. BALACLAVA: Recibida

Esto es lo que dice el CRL

•A balaclava or black head sock is worn to primarily obscure any view of the wearer

Aprovechando una oferta del LIDL pude hacerme con un par a bajo precio, pero se puede encontrar fácilmente en cualquier tienda de motociclismo, deportes, etc..

[rakso]

3. NECKSEAL: Recibido

Esto es lo que dice el CRL

•Black horizontal ribs fitted to the wearer to conceal the entire neck. No hair or skin should be visible.
OPTIONAL Level two certification (if applicable):
•Neck seal is made of leather
•Neck seal shall have a neoprene skirt that tucks into the back and chest armor.

Recibido el neckseal de cuero con falda se neopreno realizado por Aaron Landher

[rakso]

4. HOSE: Recibido

Esto es lo que dice el CRL

•Black ribbed hose is approximately 1.25 inches diameter and a length proportional to the wearer. Hose length is preferably between 15-21 inches.
•Hose connects snugly to right hose port on the helmet with no visible fastener.
OPTIONAL Level two certification (if applicable):
•Hose shall be ribbed, rubber gas mask type hose.

Recibido el tubo de goma del tipo máscara de gas. Se puede localizar fácilmente en eBay escribiendo "rubber gas mask hose". Ahora toca quitarle los conectores, limpiarlo lo mejor posible y añadirle los imanes correspondientes para sujetarlo al casco y chest box.

[rakso]

5. FLEXIBLE VAC SUIT (Flight Suit): Recibido

Esto es lo que dice el CRL

•One piece black jumpsuit with a hidden zipper in the front.
•Flight Suit is a synthetic gloss/semi gloss, smooth/texture free fabric. nylon, vinyl, faux leather, polyester, satin are suitable options.
•There are pleats on each arm beginning just above the bicep. There is a space between the top most pleat and the others.
•There is vertical detail stitching throughout the suit as seen in the reference photo.
•There is a large pleat that begins at each knee area of the suit. This large pleat comes to a soft point at the knee cap. Below this larger pleat is a gap followed smaller pleats.
•There are two large cargo pockets with velcro closure on each thigh of the suit. Cargo pockets may be padded out.
•Legs of suit shall be tucked into boots.
OPTIONAL Level two certification (if applicable):
•All detail stitching must be present

[rakso]

6. CHEST ARMOR: En proceso de construcción

Esto es lo que dice el CRL

•There is a recessed area at the top center of the chest plate
•There is a slight groove running vertical on each side of the chest that angles towards the center.
•Behind the grooves are two open ended rectangles, equally spaced, on the far edge of the armor on both sides
•Two fastener indentations, or greeblies are on both sides of the front of the chest
•Six recessed ovals are on the wearers right side just left of the fastener Indentation
OPTIONAL Level two certification (if applicable):
•The six recessed ovals and top center recessed area shall be cut out and backed with gaffer's tape.

[rakso]

7- BACK ARMOR AND YOKE: En proceso de construcción

Esto es lo que dice el CRL

•The back plate contains the "O II" design
•The yoke is one seamless piece
•The yoke portion extends over the wearer's shoulders and curves under the armpits.
•There are two, slightly curved, stacked bridges (shoulder straps) that follow the contour of the wearers shoulders attached to the top portion of the yoke. On the top of each bridge there are molded greeblies at each end.
•A piece of nylon strapping material approximately one inch wide runs in between the two greeblies
•Elastic or strapping material may be used to assist the armor fitting snugly on the sides
OPTIONAL Level two certification (if applicable):
•Shoulder bridges must match reference photo.

[rakso]

8. SHOULDER BELLS: En proceso de construcción

Esto es lo que dice el CRL

•The two bells are symmetrical and interchangeable and extend down the bicep.
•Shoulders have a small round extension at the top under the bell that butts up against the yoke
•Bells are held in place by approximately one inch wide elastic or strapping material that encircles the bicep.
•Bells may also be held in place by hidden velcro or strapping that connect to the yoke/shoulder bridges.
•There is a 2.75 inch wide, silver painted or decal First Order Cog present on each shoulder bell.

[rakso]

9. VAMBRACE ARMOR (FOREARMS): En proceso de construcción

Esto es lo que dice el CRL

•Forearms shall have a rigid rail embedded on the inside of the forearm
•Inside this rail is a detail piece with vertical rectangles, evenly spaced.
•There are also three round detail pieces spaced intermittently between the rectangles
•There are recessed grooves running vertically alongside the detail piece
•There is a horizontal "coin slot" above recessed detail piece and even with the vertical recessed lines
•Forearms shall have a box on the bottom of each wrist end. There is a square in each wrist box on the lower inside corner.
•On the bottom edge of each wrist box is a rectangle on the small edge perpendicular and closest to the wrist.
OPTIONAL Level two certification (if applicable):
•The square and rectangle on the wrist boxes and the "coin slot" shall be cut out and backed with gaffer's tape.

[rakso]

10. FLIGHT GLOVES: Recibidos

Esto es lo que dice el CRL

•Gloves are leather combat gloves or similar.
•On the top of the glove there is a one inch wide nylon strap at the wrist with a tri-glide buckle.
•No other adornments or decorative stitching shall be present
•There is a padded section on top of the hand that starts just above the wrist and covers 1/4 of the fingers above the knuckles.
OPTIONAL Level two certification (if applicable):
•Must match British Army MTP Combat gloves.

[rakso]

11. LIFE SUPPORT GEAR (CHEST BOXES): En proceso de construcción

Esto es lo que dice el CRL

•There are three separate chest boxes that are attached to the lower portion of the chest armor midline at the abdominal area of the wearer. One quarter of the chest boxes hang below the bottom edge of the chest armor
Chest Box #1
•Rectangular in shape with bottom three quarters of box stepped outwards.
•There are detail lines in the top outfacing edges.
•On the top flat surface of the box are five recessed, elongated ovals (to the wearers left)
•On the top flat, stepped out surface are five smaller recessed ovals (to the wearer’s right)
•On the bottom outfacing surface of the box are five, one inch detail squares ◦One white
◦One gray
◦One black
◦Two blue
OPTIONAL Level two certification (if applicable):
•Detail squares must match combination in reference photo. No other combinations or colors will be accepted.
Chest Box #2
•Rectangular in shape with a recessed or "stepped down" area on the top surface. In the middle of this stepped down area is a port for the hose connection to the helmet.
•There are recessed horizontal lines running up the middle front face of the box.
•Midline on the box is a silver/gray clasp or clamp.
•There is a ringed greeblie or detail piece between the hose port on the box and the hose.
•There is a black zip-tie securing the hose just above the detail piece.
OPTIONAL Level two certification (if applicable):
•Clamp shall be held in place with black elastic strap that encircles the box.
Chest Box #3
•Rectangular in shape with a one eigth thick raised piece on the top facing surface of the box.
•On top of this raised area is a two pronged/forked detail piece
•Two light caps or lenses are present towards the top front facing portion of the box, one white and one red respectively.
•Along the bottom front facing edge of the box are three rocker switches in the following combination, gray/white/gray. No other combinations will be accepted.
•Slant on rocker switches is minimal.
OPTIONAL Level two certification (if applicable):
•Lenses shall not be electronically lit.

[rakso]

12. BELTS, BELT BOXES AND EJECTION HARNESS: En proceso de construcción

Esto es lo que dice el CRL

•A nylon belt, approximately 2 inches wide, is worn around the waist. Nylon belt closes in the front with a large, parachute type buckle.
•On top of the nylon belt is a rubber belt two inches wide with velcro closure that closes on the wearer's side.
•Belt boxes and nylon pouches of various shapes and sizes are worn around the belt to the wearer's preference. A minimum of three, but no more than six may be worn.
•There is no holster present on the belt.
•A one inch wide nylon strap or ejection harness is looped over the main belt at the wearer's pelvic area and is held in place with tri-glide buckles. The strap ends are finished at a 45 degree angle.
•The ejection straps run from the main belt, down the length of the thigh to the wearer’s knees.
•There is a loop with tri-glide buckle at the bottom of the ejection strap that fully encircles the wearer's leg just above the knee.
OPTIONAL Level two certification (if applicable):
•Six total boxes/pouches shall be worn

[rakso]

13. POSITIVE GRAVITY BOOTS: Recibidas

Esto es lo que dice el CRL

•Boots closely resemble German jack boots or motorcycle riding boots.
•Boots have a flat wedge sole with no defined heel.
•Boot height ends mid calf.
•There is a forward facing strap with a snap at the outside top of the boot.
•The adjustment strap flares out larger towards the back of the boot and is in place with two snaps or rivets.
OPTIONAL Level two certification (if applicable):
Boots shall be made of leather.

[rakso]

14. ACCESIORIO OPCIONAL, SE-44c Blaster Pistol: En proceso de construcción

Esto es lo que dice el CRL

Items below are optional costume accessories. These items are not required for approval, but if present appear as described below. If adding in an accessory after initial approval, the item still needs to be submitted to local GML for approval before use.
•Scratch built or high end prop replica
•Must match specifications and colors in reference photo

Aunque no es necesario para el alta, los complementos opcionales que se deseen usar, deben ser enviados al GML para su aprobación antes de su uso por lo que en este caso, he decidido añadir el blaster a la lista de componentes para que sea validado con todo el conjunto.

Actualización 14/12/2018
------------------------------------------
Recibido el Blaster de Imperial Props 3D gracias al consejo de nuestro compañero Yiyo. Se puede contactar por FB (o buscar a Sebastián Espinosa)




Glock - Frame
Glock - Slide
Glock - Trigger 1
Glock - Trigger 2



Glock - Ammo Clip 1
Glock - Ammo Clip 2
Glock - Cocking lever



Shell - Front
Shell - Rear
Thigh Bracket



Shell Front - Right Rail
Shell Front - Left Rail
Shell Front - Details
Shell Front - Bottom Rail
Shell Front - Top Rail



End Cap - Plug
End Cap - Bolt



Visor - Body
Visor - Mount
Visor - Rail
Visor - Pulley
Visor - Detail
Visor - Red LED